Getting Solid Orange LED on Linksys Extender? Let’s Get That Fixed!

Are you continuously getting solid orange LED on your Linksys extender? Tried even soft reset and hard reset to fix the issue but nothing worked? Need not to worry! In this troubleshooting guide, we will take you through various quick fixes to resolve the issue in no time. Let’s get the ball rolling!

Why Are You Getting Solid Orange LED on Linksys Extender?

The solid orange LED on your Linksys extender affects your device badly, ranging from losing internet to damaging your device. So, it is better to find the proper reason behind the issue.

Here’s a list of some common reasons why you are getting solid orange LED on Linksys extender:

Note: This troubleshooting guide is meant to fix solid orange LED issue on any model of Linksys extender. But, in this post, we have particularly taken the example of RE6300.

  • You have not placed your Linksys extender in an open and airy area.
  • The RE6300 is receiving signal interference from unknown WiFi devices.
  • Partial Linksys extender setup also leads you to the issue.
  • Linksys extender not connected to your router.
  • An outdated firmware version on your Linksys RE6300 extender will also let you experience the orange LED issue.
  • Issue from your service provider end.
  • Linksys extender not getting sufficient power supply.
  • Power outage during Linksys extender setup.

So, now you know the reasons why you are getting solid orange LED on Linksys extender. Let’s dive into the fixes to troubleshoot the issue, shall we?

Solved: Solid Orange LED on Linksys Extender

  • Check the placement of your Linksys WiFi range extender. It should be kept in a ventilated room. Also, choose a clean and higher surface to place your RE6300.
  • It is suggested to place your Linksys extender away from windows, corners, and interference-creating unknown WiFi devices.
  • Check the wall socket you have used to plug in your Linksys extender. It must be damaged-free and shock proof.
  • Power cycle your Linksys WiFi range extender. To do so, unplug your Linksys extender from the power socket and then plug it back in again after a few minutes.
  • Update the firmware of your Linksys extender on a regular basis.
  • Complete the Linksys extender setup process correctly. On the off chance if the manual setup seems a bit tricky to you, try the Linksys RE6300 WPS setup.
  • Connect your router to the Linksys extender properly.
  • Contact your ISP. Ensure that all your internet bills are clear. Also, verify that the device (provided by them) you are using is up-to-date. It is also recommended to upgrade your internet plan.
  • Ensure that your Linksys extender is receiving a continuous and fluctuation-free power supply.

Still Facing the Same Issue?

Still getting solid orange LED on Linksys extender? Is yes, try resetting your Linksys WiFi range extender back to the factory default settings.

Yes, you read it right. The resetting process can fix many big issues with your RE6300 or any other model of Linksys extender.

To reset Linksys extender, follow the steps listed below:

  • First things first, disconnect your Linksys extender from your router, PC, laptop, and mobile device(if connected!).
  • Then, locate the reset hole on your Linksys RE6300 extender.
  • Push it using any thin, pointed, and sharp object.
  • Hold the Linksys extender reset hole for a couple of seconds.
  • Release it.
  • Connect your Linksys extender with your router and other WiFi-enabled devices in a wireless manner or using an Ethernet cable.
  • Configure your extender again using the manual setup or Linksys RE6300 WPS setup.

In the event that you are still getting solid orange LED on Linksys extender, let our highly-experienced technicians fix it for you within minutes.

Leave a Reply

Your email address will not be published. Required fields are marked *

Back To Top